View CAT3616_4694024.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

CAT3616 6-Channel Charge Pump LED Driver with EZDimt
Description
The CAT3616 is a high efficiency 1x/1.5x fractional charge pump with programmable dimming current in six LED channels. To ensure uniform brightness in LCD backlight applications, each LED channel delivers an accurate regulated current. Low noise and input ripple is achieved by operating at a constant switching frequency of 1 MHz which allows the use of small external ceramic capacitors. The 1x/1.5x fractional charge pump supports a wide range of input voltages from 3 V to 5.5 V with efficiency up to 91%, and is ideal for Li-Ion battery powered devices. Two groups of LEDs, main (MAIN1 to MAIN4) and sub (SUB1 and SUB2) are programmable through the ENM (active low) and ENS inputs. Independent current from 1 mA to 31 mA with a 1 mA step are set by toggling the ENM and ENS inputs. The enable EN input pin allows to shutdown the device with zero quiescent current. The device is available in a 16-pad TQFN package with a max height of 0.8 mm.
Features
http://onsemi.com
1 TQFN-16 HV4 SUFFIX CASE 510AE
PIN CONNECTIONS
MAIN2 MAIN3 MAIN4 SUB1 MAIN1 ENM ENS EN 1 TAB is GND VOUT VIN C1- C1+ (Top View) SUB2 GND C2+ C2-
* * * * * * * * * * * * * *
6 LED Channels with Tight Matching Independent Main and Sub Channels 1-wire EZDimt Programmable LED Current Accurate 1 mA Dimming Level Power Efficiency up to 91% Fractional Pump 1x/1.5x Low Noise Input Ripple Fixed High Frequency Operation 1 MHz "Zero" Current Shutdown Mode Soft Start and Current Limiting Short Circuit Protection Thermal Shutdown Protection 16-pad TQFN 4 mm x 4 mm Package These Devices are Pb-Free, Halogen Free/BFR Free and are RoHS Compliant Main and Sub-display Backlight Color LCD and Keypad Backlighting Cellular Phones Handheld Devices Digital Cameras
MARKING DIAGRAMS
G616 AXXX YMCC CDAH AXXX YMCC
G616 = CAT3616HV4-T2 CDAH = CAT3616HV4-GT2 A = Assembly Location XXX = Last Three Digits of Assembly Lot Number Y = Production Year (Last Digit) M = Production Month (1-9, A, B, C) CC = Country of Origin (Two Digit) Note: Two digit code for country of origin: Thailand = TH Malaysia = MY
Applications
* * * * *
ORDERING INFORMATION
Device CAT3616HV4-T2 (Note 1) CAT3616HV4-GT2 (Note 2) Package TQFN-16 (Pb-Free) TQFN-16 (Pb-Free) Shipping 2,000/ Tape & Reel 2,000/ Tape & Reel
1. Matte-Tin Plated Finish (RoHS-compliant). 2. NiPdAu Plated Finish (RoHS-compliant). 1 Publication Order Number: CAT3616/D
(c) Semiconductor Components Industries, LLC, 2010
April, 2010 - Rev. 3
CAT3616
NOTE: Unused LED channels must be connected to VOUT.
Figure 1. Typical Application Circuit
Table 1. ABSOLUTE MAXIMUM RATINGS
Parameter VIN, LEDxx voltage VOUT, C1, C2 voltage EN, ENM, ENS voltage Storage Temperature Range Junction Temperature Range Lead Temperature Rating 6 7 VIN + 0.7 V -65 to +160 -40 to +150 300 Unit V V V C C C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability.
Table 2. RECOMMENDED OPERATING CONDITIONS
Parameter VIN Ambient Temperature Range ILED per LED pin IOUT Total Output Current NOTE: Typical application circuit with external components is shown above. Range 3 to 5.5 -40 to +85 0 to 31 0 to 150 Unit V C mA mA
http://onsemi.com
2
CAT3616
Table 3. ELECTRICAL OPERATING CHARACTERISTICS
Symbol IQ Parameter Quiescent Current VIN = 3.6 V, EN = High, ambient temperature of 25C (over recommended operating conditions unless specified otherwise) Conditions 1x mode, all LEDs Off 1x mode, all LEDs On 1.5x mode, all LEDs Off VEN = 0 V 0 1 mA ILED 31 mA (ILED - ILEDAVG) / ILEDAVG 1x mode, IOUT = 120 mA 1.5x mode, IOUT = 120 mA 0.8 VOUT < 0.5 V 1x mode, VOUT > 1 V -1 1.3 165 20 2 3 3 0.5 2.2 1 60 300 1 0.4 1.3 Min Typ 0.5 2.2 3.5 0 1 31 Max Unit mA
IQSHDN ILED ILED-ACC ILED-DEV ROUT FOSC ISC_MAX IIN_MAX IEN/DIM VHI VLO TSD THYS VUVLO
Shutdown Current LED Current Range with 6 LEDs LED Current Accuracy LED Channel Matching Output Resistance (open loop) Charge Pump Frequency Output short circuit Current Limit Input Current Limit EN/DIM Pin - Input Leakage - Logic High Level - Logic Low Level Thermal Shutdown Thermal Hysteresis Undervoltage lock out (UVLO) threshold
mA mA % % W MHz mA mA mA V V C C V
Table 4. RECOMMENDED EN, ENM AND ENS TIMING
Symbol TSETP TLO THI TOFF TD TDEC Parameter EN setup from shutdown ENM, ENS program low time ENM, ENS program high time EN low time to shutdown LED current enable LED current decrement
(For 3 V VIN 5.5 V, over full ambient temperature range -40 to +125C.) Conditions Min 10 0.3 0.3 1.5 40 0.1 200 Typ Max Unit ms ms ms ms ms ms
http://onsemi.com
3
CAT3616
Figure 2. Enable LED Timing Diagram
http://onsemi.com
4
CAT3616
(VIN = 3.6 V, IOUT = 90 mA (6 LEDs at 15 mA), EN = VIN, ENM = ENS = GND, CIN = C1 = C2 = COUT = 1 mF, TAMB = 25C, unless otherwise specified.) 100 90 EFFICIENCY (%) 80 70 60 50 40 EFFICIENCY (%) 1x Mode 15 mA per LED 100 90 VIN = 4 V (1x Mode) 80 70 60 50 40 VIN = 3.2 V (1.5x Mode)
TYPICAL CHARACTERISTICS
20 mA per LED 1.5x Mode
4.2
4.0
3.8
3.6
3.4
3.2
3.0
0
50
100
150
200
INPUT VOLTAGE (V)
TOTAL LED CURRENT (mA)
Figure 3. Efficiency vs. Input Voltage (6 LEDs On)
0.8 QUIESCENT CURRENT (mA) QUIESCENT CURRENT (mA) 0.8
Figure 4. Efficiency vs. Total LED Current (6 LEDs)
0.6
0.6
0.4 6 LEDs OFF 0.2
0.4 6 LEDs OFF 0.2
0
3.0
3.2
3.4
3.6
3.8
4.0
4.2
0 -40
0
40 TEMPERATURE (C)
80
120
INPUT VOLTAGE (V)
Figure 5. Quiescent Current vs. Input Voltage (1x Mode)
5 QUIESCENT CURRENT (mA) 4 3 2 6 LEDs OFF 1 0 QUIESCENT CURRENT (mA) 5 4 3 2
Figure 6. Quiescent Current vs. Temperature (1x Mode)
6 LEDs OFF 1 0 -40
3.0
3.2
3.4
3.6
3.8
4.0
4.2
0
40 TEMPERATURE (C)
80
120
INPUT VOLTAGE (V)
Figure 7. Quiescent Current vs. Input Voltage (1.5x Mode)
Figure 8. Quiescent Current vs. Temperature (1.5x Mode)
http://onsemi.com
5
CAT3616
(VIN = 3.6 V, IOUT = 90 mA (6 LEDs at 15 mA), EN = VIN, ENM = ENS = GND, CIN = C1 = C2 = COUT = 1 mF, TAMB = 25C, unless otherwise specified.) 5.0 LED CURRENT CHANGE (%) 3.0 2.0 1.0 0 -1.0 -2.0 -3.0 -4.0 -5.0 1.5x Mode 1x Mode LED CURRENT CHANGE (%) 4.0 5.0 4.0 3.0 2.0 1.0 0 -1.0 -2.0 -3.0 -4.0 -5.0 -40 -20 0 20 40 60 80
TYPICAL CHARACTERISTICS
3.0
3.2
3.4
3.6
3.8
4.0
4.2
INPUT VOLTAGE (V)
TEMPERATURE (C)
Figure 9. LED Current Change vs. Input Voltage
1.3 CLOCK FREQUENCY (MHz) CLOCK FREQUENCY (MHz) 1.2 1.1 1.0 0.9 0.8 0.7 1.3 1.2 1.1 1.0 0.9 0.8 0.7
Figure 10. LED Current Change vs. Temperature
3.0
3.2
3.4
3.6
3.8
4.0
-40
0
40 TEMPERATURE (C)
80
120
INPUT VOLTAGE (V)
Figure 11. Oscillator Frequency vs. Input Voltage
1.0 OUTPUT RESISTANCE (W) 0.8 0.6 0.4 0.2 0 OUTPUT RESISTANCE (W) 4.0 3.5 3.0 2.5 2.0 1.5 1.0
Figure 12. Oscillator Frequency vs. Temperature
3.0
3.2
3.4
3.6
3.8
4.0
4.2
3.0
3.2
3.4
3.6
3.8
4.0
4.2
INPUT VOLTAGE (V)
INPUT VOLTAGE (V)
Figure 13. Output Resistance vs. Input Voltage (1x Mode)
Figure 14. Output Resistance vs. Input Voltage (1.5x Mode)
http://onsemi.com
6
CAT3616
(VIN = 3.6 V, IOUT = 90 mA (6 LEDs at 15 mA), EN = VIN, ENM = ENS = GND, CIN = C1 = C2 = COUT = 1 mF, TAMB = 25C, unless otherwise specified.)
TYPICAL CHARACTERISTICS
Figure 15. Power Up with 6 LEDs at 15 mA (1x Mode)
Figure 16. Power Up with 6 LEDs at 15 mA (1.5x Mode)
Figure 17. Enable Power Down Delay (1x Mode)
Figure 18. Enable Power Down Delay (1.5x Mode)
Figure 19. Switching Waveforms in 1.5x Mode
Figure 20. Operating Waveforms in 1x Mode
http://onsemi.com
7
CAT3616
(VIN = 3.6 V, IOUT = 90 mA (6 LEDs at 15 mA), EN = VIN, ENM = ENS = GND, CIN = C1 = C2 = COUT = 1 mF, TAMB = 25C, unless otherwise specified.)
TYPICAL CHARACTERISTICS
Figure 21. ENM, ENS and Output Current Dimming
Figure 22. Line Transient Response (3.6 V to 5.5 V) 1x Mode
4.0 3.5 OUTPUT VOLTAGE (V) 3.0 2.5 2.0 1.5 1.0 0.5 0 0 100 200 300 400 1x Mode
OUTPUT CURRENT (mA)
Figure 23. Foldback Current Limit
http://onsemi.com
8
CAT3616
Table 5. PIN DESCRIPTIONS
Pin # 1 2 3 4 5 6 7, 8 9, 10 11 12 13 14 15 16 TAB Name MAIN1 ENM ENS EN VOUT VIN C1-, C1+ C2-, C2+ GND SUB2 SUB1 MAIN4 MAIN3 MAIN2 TAB Function MAIN1 LED cathode terminal (if not used, connect to VOUT) (Note 3) Enable main LED (MAIN1 to MAIN4) input. Active low Enable sub LED (SUB1, SUB2) input. Active low Device enable input. Active high. Charge pump output connected to the LED anodes Supply voltage. Bucket capacitor 1 terminal Bucket capacitor 2 terminal Ground reference SUB2 LED cathode terminal (if not used, connect to VOUT) (Note 3) SUB1 LED cathode terminal (if not used, connect to VOUT) (Note 3) MAIN4 LED cathode terminal (if not used, connect to VOUT) (Note 3) MAIN3 LED cathode terminal (if not used, connect to VOUT) (Note 3) MAIN2 LED cathode terminal (if not used, connect to VOUT) (Note 3) Connect to Ground on PCB
3. MAIN1 to MAIN4, SUB1, SUB2 pins should not be left floating. They should be connected to the LED cathode, or tied to VOUT pin if not used.
Pin Function VIN is the supply pin for the charge pump. A small 1 mF ceramic bypass capacitor is required between the VIN pin and ground near the device. The operating input voltage range is up to 5.5 V. When the input supply falls below the undervoltage threshold (2 V), all LED channels are disabled. EN is the enable logic input. Logic level for high and low are set at 1.3 V and 0.4 V respectively. When EN is initially taken high, the device becomes enabled and all LED currents remain at 0 mA. To place the device into zero current shutdown mode, the EN pin must be held low for 1.5 ms or more. ENM, ENS are the active low enable/ dimming control logic inputs for respectively main and sub LED channels. The falling edge of the first pulse applied to ENM and ENS sets the current for respectively the main and sub LED channels to their full scale of 31 mA. On each consecutive falling edge of the pulse applied to ENM and ENS, the LED current is decreased by 1 mA step. On the 32nd pulse, the LED current is set to zero. The next pulse resets the current back to the full scale of 31 mA.
VOUT is the charge pump output that is connected to the LED anodes. A small 1 mF ceramic bypass capacitor is required between the VOUT pin and ground near the device. GND is the ground reference for the charge pump. The pin must be connected to the ground plane on the PCB. C1+, C1- are connected to each side of the 1 mF ceramic bucket capacitor C1. C2+, C2- are connected to each side of the 1 mF ceramic bucket capacitor C2. MAIN1-4, SUB1-2 provide the internal regulated current for each of the LED cathodes. These pins enter a high impedance zero current state whenever the device is placed in shutdown mode. In applications using less than six LEDs, the unused channels should be wired directly to VOUT. This ensures the channel is automatically disabled dissipating less than 200 mA. TAB is the exposed pad underneath the package. For best thermal performance, the tab should be soldered to the PCB and connected to the ground plane.
http://onsemi.com
9
CAT3616
Block Diagram
Figure 24. CAT3616 Functional Block Diagram
Basic Operation At power-up, the CAT3616 starts operating in 1x mode where the output will be approximately equal to the input supply voltage (less any internal voltage losses). If the output voltage is sufficient to regulate all LED currents the device remains in 1x operating mode. If the input voltage is insufficient or falls to a level where the regulated currents cannot be maintained, the device automatically switches (after 400 ms) into 1.5x mode.
In 1.5x mode, the output is approximately equal to 1.5 times the input supply voltage (less any internal voltage losses). The above sequence is repeated each and every time the chip is powered-up or is taken out of shutdown mode (via EN pin).
http://onsemi.com
10
CAT3616
LED Current Setting The LED current is controlled by toggling the input signals ENM and ENS. ENM controls the four LED channels MAIN1 to MAIN4. ENS controls the two LED lines SUB1 and SUB2. ENM and ENS work the same way. The chip must first be enabled by setting the enable input EN high. On the first ENM or ENS transition from high to low, the LED current in the associated LEDs is set to the full scale 31 mA. On each consecutive falling edge of ENM or ENS, the LED current is decreased by 1 mA. On the 32nd pulse, the LED channel is turned off and the current drops to 0 mA. One additional ENM or ENS pulse resets the full current to 31 mA, as shown on Figure 2. Consecutive pulses should be separated by 300 ns or more. Pulsing frequencies from 5 kHz up to 1 MHz are supported during dimming operations. When the EN is held low for 1.5 ms or more, the CAT3616 enters the shutdown mode and draws "zero" current. When the enable EN input is low, toggling ENM or ENS has no effect. Unused LED channels can be disabled independently by connecting the corresponding main or sub LED pin to VOUT.
Protection Mode
The driver enters a thermal shutdown mode as soon as the die temperature exceeds about +165C. When the device temperature drops down by about 20C, the device resumes normal operation.
External Components
The driver requires a total of four external 1 mF ceramic capacitors: two for decoupling input and output, and two for the charge pump. Both capacitor types X5R and X7R are recommended for the LED driver application. In the 1.5x charge pump mode, the input current ripple is kept very low by design, and an input bypass capacitor of 1 mF is sufficient. In 1x mode, the device operating in linear mode does not introduce switching noise back onto the supply.
Recommended Layout
If an LED becomes open-circuit, the output voltage VOUT is internally limited to about 5.5 V. This is to prevent the output pin from exceeding its absolute maximum rating.
In 1.5x charge pump mode, the driver switches internally at a high frequency of 1 MHz. It is recommended to minimize trace length to all four capacitors. A ground plane should cover the area under the driver IC as well as the bypass capacitors. Short connection to ground on capacitors Cin and Cout can be implemented with the use of multiple via. A copper area matching the TDFN exposed pad (GND) must be connected to the ground plane underneath. The use of multiple via improves the package heat dissipation.
http://onsemi.com
11
CAT3616
Application Information
Single Wire Dimming Application
The dimming control can be achieved through a single wire interface by connecting together all three logic input signals EN, ENM and ENS as shown on Figure 25. The common enable signal is set high to enable the driver. On the first negative going pulse, the LEDs turn full on. The
pulse low state duration (between the falling and rising edges) must be shorter than 0.5 msec. Any consecutives pulses reduce the LED current by 1 mA. The enable signal is kept low for more than 1.5 msec to turn off all the LED channels and set the driver in shutdown mode, as shown on Figure 26.
Figure 25. Single Wire Dimming Control
Figure 26. Single Enable Timing Diagram
http://onsemi.com
12
CAT3616
PACKAGE DIMENSIONS
TQFN16, 4x4 CASE 510AE-01 ISSUE A
D A DETAIL A
E
E2
PIN#1 ID D2 BOTTOM VIEW
PIN#1 INDEX AREA TOP VIEW
A1 SIDE VIEW
SYMBOL A A1 A3 b D D2 E E2 e L
MIN 0.70 0.00 0.25 3.90 2.00 3.90 2.00 0.45
NOM 0.75 0.02 0.20 REF 0.30 4.00 --- 4.00 --- 0.65 BSC ---
MAX 0.80 0.05 0.35 4.10 2.25 4.10 2.25 0.65 A L DETAIL A b e
Notes: (1) All dimensions are in millimeters. (2) Complies with JEDEC MO-220.
A1 FRONT VIEW
A3
http://onsemi.com
13
CAT3616
Example of Ordering Information (Note 6)
Prefix CAT Device # 3616 Suffix HV4 -G T2
Company ID (Optional)
Product Number 3616
Package HV4: TQFN 4 x 4 mm
Lead Finish G: NiPdAu Blank: Matte-Tin (Note 7)
Tape & Reel (Note 8) T: Tape & Reel 2: 2,000 / Reel
4. 5. 6. 7. 8.
All packages are RoHS-compliant (Lead-free, Halogen-free). The standard lead finish is NiPdAu. The device used in the above example is a CAT3616HV4-GT2 (TQFN, NiPdAu Plated Finish, Tape & Reel, 2,000/Reel). For Matte-Tin package option, please contact your nearest ON Semiconductor Sales office. For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
EZDim is a trademark of Semiconductor Components Industries, LLC.
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative
http://onsemi.com
14
CAT3616/D

▲Up To Search▲

Price & Availability of CAT3616

	To Download CAT3616 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .